=== START OF INFORMATION SECTION ===
Vendor: TOSHIBA
Product: MG10SCP20TA
Revision: PE0A
Compliance: SPC-4
User Capacity: 20,000,588,955,648 bytes [20.0 TB]
Logical block size: 4096 bytes
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000039d7833b7b1
Serial number: 84P0A09EF98J
Device type: disk
Transport protocol: SAS (SPL-4)
Local Time is: Thu Feb 26 19:43:40 2026 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature: 24 C
Drive Trip Temperature: 65 C

Manufactured in week 34 of year 2024
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 15
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 16
Elements in grown defect list: 0

Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 0 0 0 0 36166.133 0
write: 0 1 0 0 0 78.047 0

Non-medium error count: 0

SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background short Completed - 157 - [- - -]

Long (extended) Self-test duration: 103080 seconds [28.6 hours]

Background scan results log
Status: scan is active
Accumulated power on time, hours:minutes 201:13 [12073 minutes]
Number of background scans performed: 3, scan progress: 72.04%
Number of background medium scans performed: 3
Device does not support General statistics and performance logging

Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 1
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: power on
reason: power on
negotiated logical link rate: phy enabled; 12 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000039d7833b7b2
attached SAS address = 0x500605b0100b51f6
attached phy identifier = 4
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization count = 0
Phy reset problem count = 0
Phy event descriptors:
Elasticity buffer overflow count: 0
Received abandon-class OPEN_REJECT count: 0
Transmitted BREAK count: 0
Received BREAK count: 0
Transmitted SSP frame error count: 0
Received SSP frame error count: 0
relative target port id = 2
generation code = 1
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000039d7833b7b3
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization count = 0
Phy reset problem count = 0
Phy event descriptors:
Elasticity buffer overflow count: 0
Received abandon-class OPEN_REJECT count: 0
Transmitted BREAK count: 0
Received BREAK count: 0
Transmitted SSP frame error count: 0
Received SSP frame error count: 0