Revise paste NRFL01_RC CAR_transmitter_ESP32C3

//PROGRAM BY: RANDY N. CAÑADA (NOV. 2025)

//CONNECTIONS
/*CE_PIN 7
CSN_PIN 10
SCK_PIN 4
MOSI_PIN 6
MISO_PIN 5
GND-GND
VCC-5Vdc/3.3vdc

JOYSTICKS:
VRX = A1
VRY= A0
gnd-grnd
vcc-vcc

note: when you are using breakout board for nrfl01, you can supply 5vdc. If not use 3.3vdc
*/
#include <SPI.h>
#include <RF24.h>

#define CE_PIN 7
#define CSN_PIN 10

#define joyVert A0 // VRy → forward/backward
#define joyHorz A1 // VRx → turning

RF24 radio(CE_PIN, CSN_PIN);
const byte address[6] = "00001";

struct Data_Package {
  int8_t motorLeft;
  int8_t motorRight;
};

Data_Package data;

int centerVert = 0;
int centerHorz = 0;

void setup() {
  Serial.begin(115200);
  pinMode(joyVert, INPUT);
  pinMode(joyHorz, INPUT);

SPI.begin();
  //SPI.begin(4, 5, 6); // SCK, MISO, MOSI

if (!radio.begin()) {
    Serial.println("NRF24 not responding!");
    while (1);
  }

radio.openWritingPipe(address);
  radio.setChannel(100);
  radio.setPALevel(RF24_PA_LOW);
  radio.setDataRate(RF24_250KBPS);
  radio.stopListening();

// Calibrate joystick center
  Serial.println("Calibrating joystick, keep it untouched...");
  delay(2000);
  centerVert = analogRead(joyVert);
  centerHorz = analogRead(joyHorz);
  Serial.print("Center Vert: "); Serial.print(centerVert);
  Serial.print("  Center Horz: "); Serial.println(centerHorz);
  Serial.println("Calibration done!");
}

void loop() {
  int deadZone = 30;

int joyV_raw = analogRead(joyVert) - centerVert;
  int joyH_raw = analogRead(joyHorz) - centerHorz;

int joyV = 0;
  int joyH = 0;

// Map Vertical (forward/backward)
  if (abs(joyV_raw) > deadZone) {
    joyV = map(joyV_raw, -512, 512, -127, 127);
  }

// Map Horizontal (turning)
  if (abs(joyH_raw) > deadZone) {
    joyH = map(joyH_raw, -512, 512, -127, 127);
  }

// Combine for motor speeds
  int MotorLeft = joyV + joyH;
  int MotorRight = joyV - joyH;

MotorLeft = constrain(MotorLeft, -127, 127);
  MotorRight = constrain(MotorRight, -127, 127);

if (abs(MotorLeft) < 5) MotorLeft = 0;
  if (abs(MotorRight) < 5) MotorRight = 0;

data.motorLeft = MotorLeft;
  data.motorRight = MotorRight;

radio.write(&data, sizeof(Data_Package));

Serial.print("joyV_raw: "); Serial.print(joyV_raw);
  Serial.print("  joyH_raw: "); Serial.print(joyH_raw);
  Serial.print("  MotorLeft: "); Serial.print(MotorLeft);
  Serial.print("  MotorRight: "); Serial.println(MotorRight);

delay(100);
}