Revise paste "Bluetooth Detection" rev_02

/********* Pleasedontcode.com **********

Pleasedontcode thanks you for automatic code generation! Enjoy your code!

- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

- Project: "Bluetooth Detection"
	- Source Code compiled for: Arduino Uno
	- Source Code created on: 2023-12-08 06:46:17

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* scan for low energy bluetooth peripherals */
/****** SYSTEM REQUIREMENT 2 *****/
	/* scan for bluetooth periphrals and if 1 is detected */
	/* then send 9 volts to pin 13 */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include <Arduino.h>
#include <SoftwareSerial.h>

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);

/***** DEFINITION OF Software Serial *****/
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_TX_A0 = A0;
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_RX_A1 = A1;
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_TX_A2 = A2;
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_RX_A3 = A3;
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_TX_A4 = A4;
const uint8_t BLE_HC05_mySerial_PIN_SERIAL_RX_A5 = A5;
SoftwareSerial BLE_HC05_mySerial1(BLE_HC05_mySerial_PIN_SERIAL_RX_A1, BLE_HC05_mySerial_PIN_SERIAL_TX_A0);
SoftwareSerial BLE_HC05_mySerial2(BLE_HC05_mySerial_PIN_SERIAL_RX_A3, BLE_HC05_mySerial_PIN_SERIAL_TX_A2);
SoftwareSerial BLE_HC05_mySerial3(BLE_HC05_mySerial_PIN_SERIAL_RX_A5, BLE_HC05_mySerial_PIN_SERIAL_TX_A4);

void setup(void)
{
  // put your setup code here, to run once:

BLE_HC05_mySerial1.begin(9600);
  BLE_HC05_mySerial2.begin(9600);
  BLE_HC05_mySerial3.begin(9600);

pinMode(13, OUTPUT); // Pin 13 as output for sending 9 volts
}

void loop(void)
{
  // put your main code here, to run repeatedly:

/****** SYSTEM REQUIREMENT 1 *****/
  /* scan for low energy bluetooth peripherals */
  // Add your code to scan for low energy bluetooth peripherals here

/****** SYSTEM REQUIREMENT 2 *****/
  /* scan for bluetooth peripherals and if 1 is detected */
  /* then send 9 volts to pin 13 */
  // Add your code to scan for bluetooth peripherals here
  // If 1 is detected, set pin 13 to HIGH
  // Otherwise, set pin 13 to LOW
  
  // Example code to set pin 13 to HIGH if 1 is detected
  if (1 /* is detected */) {
    digitalWrite(13, HIGH);
  } else {
    digitalWrite(13, LOW);
  }

delay(1000); // Delay for 1 second

}