Revise paste MPU6050 Orientation rev_02

/********* Pleasedontcode.com **********

Pleasedontcode thanks you for automatic code generation! Enjoy your code!

- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

- Project: MPU6050 Orientation
	- Source Code NOT compiled for: Arduino Nano ESP32
	- Source Code created on: 2024-06-05 21:55:33

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* read gyroscope at maximum rate and show on serial. */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include <Wire.h>
#include <MPU6050.h>  // https://github.com/electroniccats/mpu6050

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void dmpDataReady(void);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t sensor_MPU6050_Interrupt_PIN_D2 = 2;

/***** DEFINITION OF I2C PINS *****/
const uint8_t sensor_MPU6050_I2C_PIN_SDA_A4 = A4;
const uint8_t sensor_MPU6050_I2C_PIN_SCL_A5 = A5;
const uint8_t sensor_MPU6050_I2C_SLAVE_ADDRESS = 104;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
MPU6050 mpu(sensor_MPU6050_I2C_SLAVE_ADDRESS);

/****** VARIABLES ******/
bool dmpReady = false;  // set true if DMP init was successful
uint8_t mpuIntStatus;   // holds actual interrupt status byte from MPU
uint8_t devStatus;      // return status after each device operation (0 = success, !0 = error)
uint16_t packetSize;    // expected DMP packet size (default is 42 bytes)
uint16_t fifoCount;     // count of all bytes currently in FIFO
uint8_t fifoBuffer[64]; // FIFO storage buffer

// orientation/motion vars
Quaternion q;           // [w, x, y, z]         quaternion container
VectorInt16 aa;         // [x, y, z]            accel sensor measurements
VectorInt16 aaReal;     // [x, y, z]            gravity-free accel sensor measurements
VectorInt16 aaWorld;    // [x, y, z]            world-frame accel sensor measurements
VectorFloat gravity;    // [x, y, z]            gravity vector
float ypr[3];           // [yaw, pitch, roll]   yaw/pitch/roll container and gravity vector

volatile bool mpuInterrupt = false;     // indicates whether MPU interrupt pin has gone high

void dmpDataReady() {
    mpuInterrupt = true;
}

void setup(void)
{
    // put your setup code here, to run once:
    Wire.begin(sensor_MPU6050_I2C_PIN_SDA_A4, sensor_MPU6050_I2C_PIN_SCL_A5);
    Wire.setClock(400000); // 400kHz I2C clock. Comment this line if having compilation difficulties

Serial.begin(115200);
    while (!Serial); // wait for Leonardo enumeration, others continue immediately

Serial.println(F("Initializing I2C devices..."));
    mpu.initialize();
    pinMode(sensor_MPU6050_Interrupt_PIN_D2, INPUT);

// verify connection
    Serial.println(mpu.testConnection() ? F("MPU6050 connection successful") : F("MPU6050 connection failed"));

// load and configure the DMP
    Serial.println(F("Initializing DMP..."));
    devStatus = mpu.dmpInitialize();

// supply your own gyro offsets here, scaled for min sensitivity
    mpu.setXGyroOffset(220);
    mpu.setYGyroOffset(76);
    mpu.setZGyroOffset(-85);
    mpu.setZAccelOffset(1788); // 1688 factory default for my test chip

// make sure it worked (returns 0 if so)
    if (devStatus == 0) {
        // turn on the DMP, now that it's ready
        Serial.println(F("Enabling DMP..."));
        mpu.setDMPEnabled(true);

// enable Arduino interrupt detection
        attachInterrupt(digitalPinToInterrupt(sensor_MPU6050_Interrupt_PIN_D2), dmpDataReady, RISING);
        mpuIntStatus = mpu.getIntStatus();

// set our DMP Ready flag so the main loop() function knows it's okay to use it
        Serial.println(F("DMP ready! Waiting for first interrupt..."));
        dmpReady = true;

// get expected DMP packet size for later comparison
        packetSize = mpu.dmpGetFIFOPacketSize();
    } else {
        // ERROR!
        // 1 = initial memory load failed
        // 2 = DMP configuration updates failed
        // (if it's going to break, usually the code will be 1)
        Serial.print(F("DMP Initialization failed (code "));
        Serial.print(devStatus);
        Serial.println(F(")"));
    }
}

void loop(void)
{
    // put your main code here, to run repeatedly:
    if (!dmpReady) return;

// wait for MPU interrupt or extra packet(s) available
    while (!mpuInterrupt && fifoCount < packetSize) {
        // other program behavior stuff here
        // .
        // .
        // .
        // if you are really paranoid you can frequently test in between other
        // stuff to see if mpuInterrupt is true, and if so, "break;" from the
        // while() loop to immediately process the MPU data
        // .
        // .
        // .
    }

// reset interrupt flag and get INT_STATUS byte
    mpuInterrupt = false;
    mpuIntStatus = mpu.getIntStatus();

// get current FIFO count
    fifoCount = mpu.getFIFOCount();

// check for overflow (this should never happen unless our code is too inefficient)
    if ((mpuIntStatus & 0x10) || fifoCount == 1024) {
        // reset so we can continue cleanly
        mpu.resetFIFO();
        Serial.println(F("FIFO overflow!"));

// otherwise, check for DMP data ready interrupt (this should happen frequently)
    } else if (mpuIntStatus & 0x02) {
        // wait for correct available data length, should be a VERY short wait
        while (fifoCount < packetSize) fifoCount = mpu.getFIFOCount();

// read a packet from FIFO
        mpu.getFIFOBytes(fifoBuffer, packetSize);

// track FIFO count here in case there is > 1 packet available
        // (this lets us immediately read more without waiting for an interrupt)
        fifoCount -= packetSize;

// display Euler angles in degrees
        mpu.dmpGetQuaternion(&q, fifoBuffer);
        mpu.dmpGetGravity(&gravity, &q);
        mpu.dmpGetYawPitchRoll(ypr, &q, &gravity);
        Serial.print("ypr\t");
        Serial.print(ypr[0] * 180/M_PI);
        Serial.print("\t");
        Serial.print(ypr[1] * 180/M_PI);
        Serial.print("\t");
        Serial.println(ypr[2] * 180/M_PI);

// read raw gyroscope measurements at the maximum rate
        VectorInt16 gyroscope;
        mpu.getRotation(&gyroscope);
        Serial.print("Gyroscope\t");
        Serial.print("X: ");
        Serial.print(gyroscope.x);
        Serial.print("\tY: ");
        Serial.print(gyroscope.y);
        Serial.print("\tZ: ");
        Serial.println(gyroscope.z);
    }
}