Revise paste ESP8266 Temperature Sensor to Server

#include <Arduino.h>

#include <ESP8266WiFi.h>
#include <ESP8266WiFiMulti.h>

#include <ESP8266HTTPClient.h>

#include <WiFiClient.h>
#include "DHT.h"

#define room "office"

#define DHTPIN 2     // Digital pin connected to the DHT sensor
#define DHTTYPE DHT11   // DHT 11
DHT dht(DHTPIN, DHTTYPE);

ESP8266WiFiMulti WiFiMulti;

void setup() {

Serial.begin(115200);
  // Serial.setDebugOutput(true);

Serial.println();
  Serial.println();
  Serial.println();

for (uint8_t t = 4; t > 0; t--) {
    Serial.printf("[SETUP] WAIT %d...\n", t);
    Serial.flush();
    delay(1000);
  }

WiFi.mode(WIFI_STA);
  WiFiMulti.addAP("<SSID>", "<WPA-Phrase>");

dht.begin();
}

void loop() {
  // wait for WiFi connection
  if ((WiFiMulti.run() == WL_CONNECTED)) {

///////////////////////DHT///////////////////////
  // Wait a few seconds between measurements.
  delay(2000);

// Reading temperature or humidity takes about 250 milliseconds!
  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
  float h = dht.readHumidity();
  String H = String(h);
  // Read temperature as Celsius (the default)
  float t = dht.readTemperature();
  // Read temperature as Fahrenheit (isFahrenheit = true)
  float f = dht.readTemperature(true);

// Check if any reads failed and exit early (to try again).
  if (isnan(h) || isnan(t) || isnan(f)) {
    Serial.println(F("Failed to read from DHT sensor!"));
    return;
  }

// Compute heat index in Fahrenheit (the default)
  float hif = dht.computeHeatIndex(f, h);
  String temp_f = String(f);
  
  // Compute heat index in Celsius (isFahreheit = false)
  float hic = dht.computeHeatIndex(t, h, false);

Serial.print(F("Humidity: "));
  Serial.print(h);
  Serial.print(F("%  Temperature: "));
  Serial.print(t);
  Serial.print(F("°C "));
  Serial.print(f);
  Serial.print(F("°F  Heat index: "));
  Serial.print(hic);
  Serial.print(F("°C "));
  Serial.print(hif);
  Serial.println(F("°F"));
  //////////END DHT///////////////////

WiFiClient client;

HTTPClient http;

Serial.print("[HTTP] begin...\n");
    
    String url = "http://site.com/esp/temp_log/log.php?key=1234&temp=" + temp_f + "&hum=" + h + "&room=" + room;
    Serial.println(url);
    if (http.begin(client, url)) {  // HTTP

Serial.print("[HTTP] GET...\n");
      // start connection and send HTTP header
      int httpCode = http.GET();

// httpCode will be negative on error
      if (httpCode > 0) {
        // HTTP header has been send and Server response header has been handled
        Serial.printf("[HTTP] GET... code: %d\n", httpCode);

// file found at server
        if (httpCode == HTTP_CODE_OK || httpCode == HTTP_CODE_MOVED_PERMANENTLY) {
          String payload = http.getString();
          Serial.println(payload);
        }
      } else {
        Serial.printf("[HTTP] GET... failed, error: %s\n", http.errorToString(httpCode).c_str());
      }

http.end();
    } else {
      Serial.printf("[HTTP} Unable to connect\n");
    }
  }

delay(60000);
}