Revise paste "Sensor-Driven Actions" rev_01

/********* Pleasedontcode.com **********

Pleasedontcode thanks you for automatic code generation! Enjoy your code!

- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

- Project: "Sensor-Driven Actions"
	- Source Code NOT compiled for: ESP32 DevKit V1
	- Source Code created on: 2024-06-17 10:33:34

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* Rotate servo1 to 4 from 0 to 180 degree, when */
	/* pushbutto light led for 200ms, if ir1 to ir4 > 50% */
	/* rotate servo 1 to servo 4 to 0 degree */
/****** SYSTEM REQUIREMENT 2 *****/
	/* Rotate Servo1 from 0 to 180 degrees when */
	/* LaserButton (D4) is pressed. Light up Laser1 LED */
	/* (D16) for 200ms if IR1 (D14) and IR2 (D26) */
	/* readings are above 50%. Then, reset Servo1 to 0 */
	/* degrees. */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include <EasyButton.h>    //https://github.com/evert-arias/EasyButton
#include <Deneyap_Servo.h> //https://github.com/deneyapkart/deneyap-servo-arduino-library

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void onLaserButtonPressed(); // Function prototype for button press callback
void updateOutputs(); // Function prototype for updating outputs
void rotateServo(int start, int end); // Function prototype for rotating servo

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t LaserButton_PushButton_PIN_D4 = 4;

/***** DEFINITION OF ANALOG INPUT PINS *****/
const uint8_t IR1_Potentiometer_Vout_PIN_D14 = 14;
const uint8_t IR2_Potentiometer_Vout_PIN_D26 = 26;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t Laser1_LED_PIN_D16 = 16;

/***** DEFINITION OF PWM OUTPUT PINS *****/
const uint8_t Servo1_Servomotor_PWMSignal_PIN_D13 = 13;

/***** DEFINITION OF OUTPUT RAW VARIABLES *****/
/***** used to store raw data *****/
bool Laser1_LED_PIN_D16_rawData = 0;
uint8_t Servo1_Servomotor_PWMSignal_PIN_D13_rawData = 0;

/***** DEFINITION OF OUTPUT PHYSICAL VARIABLES *****/
/***** used to store data after characteristic curve transformation *****/
float Laser1_LED_PIN_D16_phyData = 0.0;
float Servo1_Servomotor_PWMSignal_PIN_D13_phyData = 0.0;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
EasyButton laserButton(LaserButton_PushButton_PIN_D4); // Initialize EasyButton instance
Servo myservo; // Initialize Servo instance

void setup(void)
{
    // put your setup code here, to run once:
    Serial.begin(115200);

pinMode(LaserButton_PushButton_PIN_D4, INPUT_PULLUP);
    pinMode(IR1_Potentiometer_Vout_PIN_D14, INPUT);
    pinMode(IR2_Potentiometer_Vout_PIN_D26, INPUT);

pinMode(Laser1_LED_PIN_D16, OUTPUT);
    pinMode(Servo1_Servomotor_PWMSignal_PIN_D13, OUTPUT);

laserButton.begin(); // Initialize the button
    laserButton.onPressed(onLaserButtonPressed); // Set the callback for button press

myservo.attach(Servo1_Servomotor_PWMSignal_PIN_D13); // Attach the servo to pin D13
}

void loop(void)
{
    // put your main code here, to run repeatedly:
    laserButton.read(); // Read the button state
    updateOutputs(); // Refresh output data
}

void onLaserButtonPressed() {
    Serial.println("Laser button pressed");

// Read IR sensor values
    int ir1Value = analogRead(IR1_Potentiometer_Vout_PIN_D14);
    int ir2Value = analogRead(IR2_Potentiometer_Vout_PIN_D26);

// Check if IR sensor values are above 50%
    if (ir1Value > 2048 && ir2Value > 2048) {
        // Light up Laser1 LED for 200ms
        digitalWrite(Laser1_LED_PIN_D16, HIGH);
        delay(200);
        digitalWrite(Laser1_LED_PIN_D16, LOW);

// Rotate Servo1 from 0 to 180 degrees
        rotateServo(0, 180);
        delay(200); // Wait for 200ms

// Reset Servo1 to 0 degrees
        rotateServo(180, 0);
    }
}

void updateOutputs()
{
    digitalWrite(Laser1_LED_PIN_D16, Laser1_LED_PIN_D16_rawData);
    myservo.write(Servo1_Servomotor_PWMSignal_PIN_D13_rawData); // Update servo position
}

void rotateServo(int start, int end) {
    if (start < end) {
        for (int pos = start; pos <= end; pos += 15) {
            myservo.write(pos);
            delay(100);
        }
    } else {
        for (int pos = start; pos >= end; pos -= 15) {
            myservo.write(pos);
            delay(100);
        }
    }
}

/* END CODE */