/********* Pleasedontcode.com **********

	Pleasedontcode thanks you for automatic code generation! Enjoy your code!

	- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

	- Project: "Digital Input/Output"
	- Source Code compiled for: Arduino Uno
	- Source Code created on: 2024-04-07 10:06:03

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* when the easy button was pressed, the green led */
	/* flashed 10 times */
/****** SYSTEM REQUIREMENT 2 *****/
	/* when the green led stops turn on the red led for */
	/* 15 seconds */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include <EasyButton.h>	//https://github.com/evert-arias/EasyButton

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void updateOutputs(void);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t tilt_PushButton_PIN_D2 = 2;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t red_LED_PIN_D3 = 3;
const uint8_t green_LED_PIN_D4 = 4;
const uint8_t bazer_PassiveBuzzer_Signal_PIN_D5 = 5;

/***** DEFINITION OF OUTPUT RAW VARIABLES *****/
/***** used to store raw data *****/
bool red_LED_PIN_D3_rawData = 0;
bool green_LED_PIN_D4_rawData = 0;
bool bazer_PassiveBuzzer_Signal_PIN_D5_rawData = 0;

/***** DEFINITION OF OUTPUT PHYSICAL VARIABLES *****/
/***** used to store data after characteristic curve transformation *****/
float red_LED_PIN_D3_phyData = 0.0;
float green_LED_PIN_D4_phyData = 0.0;
float bazer_PassiveBuzzer_Signal_PIN_D5_phyData = 0.0;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
EasyButton tilt_PushButton(tilt_PushButton_PIN_D2);

bool isButtonPressed = false;
int blinkCount = 0;

void setup(void)
{
  // put your setup code here, to run once:
  pinMode(tilt_PushButton_PIN_D2, INPUT_PULLUP);

  pinMode(red_LED_PIN_D3, OUTPUT);
  pinMode(green_LED_PIN_D4, OUTPUT);
  pinMode(bazer_PassiveBuzzer_Signal_PIN_D5, OUTPUT);

  tilt_PushButton.begin();
  tilt_PushButton.onPressed([]() {
    // Button pressed event handler
    Serial.println("Button pressed");
    isButtonPressed = true;
  });
}

void loop(void)
{
  // put your main code here, to run repeatedly:
  updateOutputs(); // Refresh output data

  tilt_PushButton.read(); // Read button state

  if (isButtonPressed) {
    // Flashes the green LED 10 times
    if (blinkCount < 10) {
      digitalWrite(green_LED_PIN_D4, HIGH);
      delay(500);
      digitalWrite(green_LED_PIN_D4, LOW);
      delay(500);
      blinkCount++;
    } else {
      // Turn on the red LED for 15 seconds
      digitalWrite(green_LED_PIN_D4, LOW);
      digitalWrite(red_LED_PIN_D3, HIGH);
      delay(15000);
      digitalWrite(red_LED_PIN_D3, LOW);
      isButtonPressed = false;
      blinkCount = 0;
    }
  }
}

void updateOutputs()
{
  digitalWrite(red_LED_PIN_D3, red_LED_PIN_D3_rawData);
  digitalWrite(green_LED_PIN_D4, green_LED_PIN_D4_rawData);
  digitalWrite(bazer_PassiveBuzzer_Signal_PIN_D5, bazer_PassiveBuzzer_Signal_PIN_D5_rawData);
}