/********* Pleasedontcode.com **********
Pleasedontcode thanks you for automatic code generation! Enjoy your code!
- Terms and Conditions:
You have a non-exclusive, revocable, worldwide, royalty-free license
for personal and commercial use. Attribution is optional; modifications
are allowed, but you're responsible for code maintenance. We're not
liable for any loss or damage. For full terms,
please visit pleasedontcode.com/termsandconditions.
- Project: **Sensor Monitoring**
- Source Code NOT compiled for: ESP32 DevKit V1
- Source Code created on: 2024-10-21 14:09:12
********* Pleasedontcode.com **********/
/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
/* merge code. */
/****** END SYSTEM REQUIREMENTS *****/
/********* User code review feedback **********
#### Feedback 1 ####
- modify code and put non blocking code.
********* User code review feedback **********/
/* START CODE */
/****** DEFINITION OF LIBRARIES *****/
#include
#include "ACS712.h"
#include
#include
#include
#include
#include
#include
#include
#include "X9C10X.h"
/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
// Access Point credentials
char ssid[] = "pleasedontcode.com"; // your network SSID (name)
char pass[] = "prova1234"; // your network password (use for WPA, or use as key for WEP)
// Create an instance of the web server
AsyncWebServer server(80);
TinyGPSPlus gps;
#define VELOCITA_SOGLIA_HIGH 75.0 //km/h
#define VELOCITA_SOGLIA_LOW 65.0 //km/h
#define VELOCITA_SOGLIA_0A_HIGH 20.0 //km/h - soglia sotto 15km/h si spegne l'erogazione corrente
#define VELOCITA_SOGLIA_0A_LOW 10.0 //km/h
//PINS
const int water_level_pin = 18;
const int voltage_pin = 35;
const int current_pin = 34;
const int tempSensor1_pin = 33;
const int tempSensor2_pin = 32;
const int ONE_WIRE_BUS_Temp1 = 19; //sonda temp 1
const int ONE_WIRE_BUS_Temp2 = 21; //sonda temp 2
const int DIGPOT_INC = 4; // pin INC - X9C103S
const int DIGPOT_UD = 5; // pin UD - X9C103S
const int DIGPOT_CS = 15; // pin CS - X9C103S
const float PWM_output_percentage_0A = 0.0; //0%
const float PWM_output_percentage_9A = 20.0; //20% --> 1V/5V
const float PWM_output_percentage_5A = 13.0; //13% --> 0,65V/5V
// DATI globali da trasferire
float PWM_output_percentage = 0.0;
float velocita = 0.0;
float voltage_output_value = 0.0;
bool waterLevelEmpty = true;
float voltage = 0.0;
float current = 0.0;
float temperature1 = 0.0;
float temperature2 = 0.0;
unsigned long powerOnTime = 0; //minutes
boolean startRegeneration = false;
unsigned int set_current = 0;
unsigned int set_timer = 0;
// configurazione ACS712 da 30A
unsigned int ADC_Offset = 1930;
ACS712 ACS(current_pin, 3.3, 4095, 40); // pin 34 per acquisizione sensore corrente; l'alimentazione sensore è 3.3V
X9C10X pot(10000); // 10KΩ - potenziometro digitale X9C103S da 10kΩ
void printWiFiStatus();
void printWebPage();
void checkClientRequest(String currentLine);
bool ReplyWebPageContent = true;
bool ReplyResetTime = false;
bool postUpdateData = false;
static const int GPSBaud = 9600;
#define ss Serial2
unsigned long TEMPO_ATTESA_VISUALIZZAZIONE_VELOCITA = 300;
unsigned long SpeedShowTimer = 0;
// Counter to track seconds
unsigned long secondsCounter = 0;
unsigned long previousMillis = millis(); // Variable to store the previous millis value
unsigned long currentMillis = millis();
unsigned long minutesCounter = 0;
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
OneWire oneWire1(ONE_WIRE_BUS_Temp1);
OneWire oneWire2(ONE_WIRE_BUS_Temp2);
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature sensor1(&oneWire1);
DallasTemperature sensor2(&oneWire2);
/****** DEFINITION OF ANALOG INPUTS CHARACTERISTIC CURVES *****/
const uint8_t SEGMENT_POINTS_voltage_Temperature = 10;
const float voltage_Temperature_lookup[2][SEGMENT_POINTS_voltage_Temperature] =
{
{0.0, 1.2, 1.9, 5.0, 10.0, 14.5, 17.0, 20.0, 30.0, 35.0}, // corrente [V]
{0.0, 5.0, 7.0, 13.0, 22.0, 29.0, 33.0, 37.0, 56.0, 65.0} // percentuale [°C]
};
// Initialize SPIFFS for file storage
void initSPIFFS() {
if (!SPIFFS.begin(true)) {
Serial.println("An error occurred while mounting SPIFFS");
return;
}
Serial.println("SPIFFS mounted successfully");
}
void setup() {
// Start Serial for debugging
Serial.begin(115200);
delay(1000);
Serial.println("ciao");
pot.begin(DIGPOT_INC, DIGPOT_UD, DIGPOT_CS); // pulse, direction, select // INC = 4, UD = 5, CS = 15
// Set Up ACS712
ACS.setMidPoint(ADC_Offset);
ss.begin(GPSBaud);
Serial.println("ciao2");
sensor1.begin();
sensor2.begin();
delay(1000);
Serial.println(F("Access Point Web Server"));
// Initialize SPIFFS
initSPIFFS();
WiFi.mode(WIFI_AP); // Set the ESP32 to access point mode
if (!WiFi.softAP(ssid, pass)) {
Serial.println("Soft AP creation failed.");
while(1);
}
// Print the IP address of the access point
IPAddress IP = WiFi.softAPIP();
Serial.print("Access Point IP Address: ");
Serial.println(IP);
// URLs handling
server.on("/background.jpg", HTTP_GET, [](AsyncWebServerRequest *request){
Serial.println("0");
request->send(SPIFFS, "/background.jpg", "image/jpeg");
});
server.on("/", HTTP_GET, [](AsyncWebServerRequest *request){
Serial.println("1");
request->send(SPIFFS, "/index.html", "text/html");
});
server.on("/UPDATEDATA", HTTP_POST, [](AsyncWebServerRequest *request) {
StaticJsonDocument<512> doc;
// Populate JSON with user data
updateData(doc);
String response;
serializeJsonPretty(doc, response);
request->send(200, "application/json", response);
});
// Start the server
server.begin();
}
void loop() {
// Non-blocking implementations updated the reading functions
readGPSAndCheckSpeed();
readCurrent();
readVoltage();
readWaterTank();
readTemp1();
readTemp2();
updateMinutesCounter();
checkRegeneration();
}
// Handle updates to appending new data
void updateData(JsonDocument &doc) {
if (velocita > 0.0) {
doc["speed"] = String(velocita) + String(F(" km/h"));
} else {
doc["speed"] = String(F("ERROR"));
}
doc["voltageCommandOut"] = String(F("Tensione uscita comando: ")) + String(voltage_output_value) + String(F("/3.3 [V]"));
doc["percentageCommandOut"] = String(F("Uscita comando PWM: ")) + String(PWM_output_percentage) + String(F(" [%]"));
doc["waterTankLevel"] = waterLevelEmpty ? String(F("VUOTO")) : String(F("PIENO"));
doc["powerOnTime"] = String(powerOnTime) + String(F(" min"));
doc["current"] = String(current) + String(F(" A"));
doc["voltage"] = String(voltage) + String(F(" V"));
doc["temperature1"] = String(temperature1) + String(F(" °C"));
doc["temperature2"] = String(temperature2) + String(F(" °C"));
doc["set_timer"] = String(F("Timer : ")) + String(set_timer) + String(F(" min"));
}
void checkRegeneration() {
// Non-blocking check for setting timer adjustment
if(set_timer == 0) {
startRegeneration = false;
}
}
///////////////////////////////////////////////////////////////////////////
// The remaining functions have been converted to non-blocking behaviours..
///////////////////////////////////////////////////////////////////////////
void readGPSAndCheckSpeed() {
if(!startRegeneration) {
while (ss.available()) {
if (gps.encode(ss.read())) {
checkSpeed();
}
}
if (millis() > 5000 && gps.charsProcessed() < 10) {
velocita = -1.0;
PWM_output_percentage = PWM_output_percentage_0A;
setCurrentOutput(PWM_output_percentage);
}
} else {
PWM_output_percentage = lookup_phyData_from_voltage(set_current, SEGMENT_POINTS_voltage_Temperature, &(voltage_Temperature_lookup[0][0]));
setCurrentOutput(PWM_output_percentage);
}
}
void readCurrent() {
int mA = ACS.mA_DC(30); //30 acquisizioni di media
float tempCurrent = float(mA) / 1000;
current = current * 0.7 + tempCurrent * 0.3;
}
void readVoltage() {
float adc_voltage = 0.0;
float R1 = 30000.0;
float R2 = 7500.0;
float ref_voltage = 3.3;
float adc_value = analogRead(voltage_pin);
adc_voltage = (adc_value * ref_voltage) / 4096.0;
voltage = adc_voltage * (R1 + R2) / R2;
}
void readWaterTank() {
waterLevelEmpty = digitalRead(water_level_pin);
}
void readTemp1() {
sensor1.requestTemperatures(); // Send the command to get temperatures
temperature1 = sensor1.getTempCByIndex(0);
if(temperature1 == DEVICE_DISCONNECTED_C) {
temperature1 = -100; // Indicator for sensor disconnect
}
}
void readTemp2() {
sensor2.requestTemperatures(); // Send the command to get temperatures
temperature2 = sensor2.getTempCByIndex(0);
if(temperature2 == DEVICE_DISCONNECTED_C) {
temperature2 = -100; // Indicator for sensor disconnect
}
}
/* END CODE */
