smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.0-36-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus
Device Model: ST3160023AS
Serial Number: 5MT2AQAW
Firmware Version: 3.42
User Capacity: 160,041,885,696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-6 T13/1410D revision 2
Local Time is: Fri Dec 26 13:20:16 2014 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 94) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 051 040 006 - 63955257
3 Spin_Up_Time PO---- 097 096 000 - 0
4 Start_Stop_Count -O--CK 035 035 020 - 67346
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1
7 Seek_Error_Rate POSR-- 077 060 030 - 56421522
9 Power_On_Hours -O--CK 092 092 000 - 7394
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 098 098 020 - 2687
194 Temperature_Celsius -O---K 033 061 000 - 33 (0 18 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 051 040 000 - 63955257
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xff GPL - 23552 Reserved

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 107 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 107 [6] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:02:02.165 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:02:02.164 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:02:02.157 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:58.286 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:58.286 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 106 [5] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:50.454 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:50.446 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:58.286 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:58.286 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 105 [4] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:50.454 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:50.446 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:50.439 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.439 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 104 [3] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:50.454 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:50.446 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:50.439 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.439 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 103 [2] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:42.552 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:42.546 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:42.545 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:42.539 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:38.598 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 102 [1] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:42.552 READ DMA
ec 00 00 00 01 00 ff ff 00 ff ff 00 00 00:01:42.546 IDENTIFY DEVICE
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:42.545 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:42.539 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:38.598 SET FEATURES [Set transfer mode]

Error 101 [0] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:34.614 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:30.722 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:30.722 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:30.714 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:38.598 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 100 [19] occurred at disk power-on lifetime: 7203 hours (300 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 04 00 cb 48 04 48 e0 00 Error: UNC at LBA = 0x400cb480448 = 4401457005640

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 cb 00 04 48 e0 00 00:01:34.614 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:30.722 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 01 00 00 ff ff 00 ff ff a0 00 00:01:30.722 IDENTIFY DEVICE
ef 00 03 00 46 00 ff ff 00 ff ff a0 00 00:01:30.714 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:30.706 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11) not supported