/********* Pleasedontcode.com **********

	Pleasedontcode thanks you for automatic code generation! Enjoy your code!

	- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

	- Project: H2S Monitor
	- Source Code NOT compiled for: Arduino Nano ESP32
	- Source Code created on: 2024-07-23 08:08:09

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* Design an H2S detection system with the MQ136 */
	/* sensor. The system should capture digital and */
	/* analog outputs, send data to a cloud server for */
	/* remote monitoring, and use an LCD and buzzer to */
	/* alert users of high H2S concentrations. */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include 
#include 	//https://github.com/miguel5612/MQSensorsLib
#include 	//https://github.com/offcircuit/LCDIC2
#include  // Include WiFi library for cloud communication
#include  // Include HTTP client for sending data to the cloud

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void updateOutputs(void);
void sendDataToCloud(float h2sConcentration);
void alertUser(float h2sConcentration);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t myHydro_MQ136_DOUT_PIN_D2 = 2;

/***** DEFINITION OF ANALOG INPUT PINS *****/
const uint8_t myHydro_MQ136_AOUT_PIN_A0 = A0;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t strip_WS2812_DIN_PIN_D3 = 3;
const uint8_t strip_WS2812B_DIN_PIN_D4 = 4;
const uint8_t buzzerPin = 5; // Define buzzer pin

/***** DEFINITION OF I2C PINS *****/
const uint8_t LCD1602_Display_LCD1602I2C_I2C_PIN_SDA_A4 = A4;
const uint8_t LCD1602_Display_LCD1602I2C_I2C_PIN_SCL_A5 = A5;
const uint8_t LCD1602_Display_LCD1602I2C_I2C_SLAVE_ADDRESS = 39;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES *****/
// Definitions for MQ136 sensor
#define placa "Arduino Nano ESP32"
#define Voltage_Resolution 5
#define ADC_Bit_Resolution 10 // For Arduino Nano ESP32
#define RatioMQ136CleanAir 3.6 // RS / R0 = 3.6 ppm
#define type "MQ-136" // MQ136

// Declare Sensor
MQUnifiedsensor MQ136(placa, Voltage_Resolution, ADC_Bit_Resolution, myHydro_MQ136_AOUT_PIN_A0, type);

// Declare LCD object using the correct constructor
LCDIC2 lcd(LCD1602_Display_LCD1602I2C_I2C_SLAVE_ADDRESS, 16, 2); // I2C address, width, height

// WiFi credentials
const char* ssid = "your_SSID"; // Replace with your network SSID
const char* password = "your_PASSWORD"; // Replace with your network password

void setup(void)
{
	// Initialize digital input and output pins
	pinMode(myHydro_MQ136_DOUT_PIN_D2, INPUT_PULLUP);
	pinMode(myHydro_MQ136_AOUT_PIN_A0, INPUT);
	pinMode(strip_WS2812_DIN_PIN_D3, OUTPUT);
	pinMode(strip_WS2812B_DIN_PIN_D4, OUTPUT);
	pinMode(buzzerPin, OUTPUT); // Set buzzer pin as output

	// Initialize the MQ136 sensor
	MQ136.init(); 

	// Set regression method and coefficients for MQ136
	MQ136.setRegressionMethod(1); // _PPM = a * ratio^b
	MQ136.setA(36.737); 
	MQ136.setB(-3.536); // Configure the equation to calculate H2S Concentration

	// Calibrate the sensor
	Serial.begin(9600); // Initialize serial communication
	Serial.print("Calibrating please wait.");
	float calcR0 = 0;
	for(int i = 1; i <= 10; i++) {
		MQ136.update(); // Update data, the Arduino will read the voltage from the analog pin
		calcR0 += MQ136.calibrate(RatioMQ136CleanAir);
		Serial.print(".");
	}
	MQ136.setR0(calcR0 / 10);
	Serial.println("  done!");

	// Check for connection issues
	if(isinf(calcR0)) {
		Serial.println("Warning: Connection issue, R0 is infinite (Open circuit detected) please check your wiring and supply");
		while(1);
	}
	if(calcR0 == 0) {
		Serial.println("Warning: Connection issue found, R0 is zero (Analog pin shorts to ground) please check your wiring and supply");
		while(1);
	}

	// Enable serial debugging
	MQ136.serialDebug(true);

	// Initialize the LCD
	lcd.begin();
	lcd.print("Initializing...");

	// Connect to WiFi
	WiFi.begin(ssid, password);
	while (WiFi.status() != WL_CONNECTED) {
		delay(1000);
		Serial.println("Connecting to WiFi...");
	}
	Serial.println("Connected to WiFi");
}

void loop(void)
{
	// Refresh output data
	updateOutputs(); 
	MQ136.update(); // Update data from the sensor
	MQ136.readSensor(); // Read sensor data
	MQ136.serialDebug(); // Print sensor data to serial

	float h2sConcentration = MQ136.getPPM(); // Get H2S concentration in PPM
	lcd.setCursor(0, 0);
	lcd.print("H2S: ");
	lcd.print(h2sConcentration);
	lcd.print(" ppm");

	sendDataToCloud(h2sConcentration); // Send data to cloud
	alertUser(h2sConcentration); // Alert user if concentration is high

	delay(1000); // Delay for a second before next loop
}

void updateOutputs()
{
	// Update digital outputs (example placeholder, replace with actual data)
	digitalWrite(strip_WS2812_DIN_PIN_D3, LOW); // Placeholder for WS2812 strip data
	digitalWrite(strip_WS2812B_DIN_PIN_D4, LOW); // Placeholder for WS2812B strip data
}

void sendDataToCloud(float h2sConcentration) {
	// Create HTTP client
	HTTPClient http;
	http.begin("http://your-cloud-server.com/api/h2s"); // Replace with your cloud server URL
	http.addHeader("Content-Type", "application/json");

	// Create JSON payload
	String jsonPayload = "{\"h2s_concentration\": ";
	jsonPayload += h2sConcentration;
	jsonPayload += "}";

	// Send POST request
	int httpResponseCode = http.POST(jsonPayload);

	if (httpResponseCode > 0) {
		Serial.printf("HTTP Response code: %d\n", httpResponseCode);
	} else {
		Serial.printf("Error sending data: %s\n", http.errorToString(httpResponseCode).c_str());
	}

	http.end(); // Free resources
}

void alertUser(float h2sConcentration) {
	if (h2sConcentration > 10.0) { // Threshold for alerting
		digitalWrite(buzzerPin, HIGH); // Turn on buzzer
		delay(1000); // Buzzer on for 1 second
		digitalWrite(buzzerPin, LOW); // Turn off buzzer
	}
}

/* END CODE */