/********* Pleasedontcode.com **********

	Pleasedontcode thanks you for automatic code generation! Enjoy your code!

	- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

	- Project: Scanner
	- Source Code compiled for: Arduino Pro Mini 3.3V
	- Source Code created on: 2023-11-11 15:32:42
	- Source Code generated by: AlexWind

********* Pleasedontcode.com **********/
/****** DEFINITION OF LIBRARIES *****/
#include 
#include 
#include 
#include 

/****** SYSTEM REQUIREMENT 1 *****/
/* every time the button is pressed 3 times, so read */
/* sensor and provide information on serial monitor. */
/****** SYSTEM REQUIREMENT 2 *****/
/* if HC05 read before the character 'o' and then the */
/* character 'k', so switch off the led. */

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t pulsante_PushButton_PIN_D3 = 3;
const uint8_t sensor_DS18B20_DQ_PIN_D5 = 5;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t led_LED_PIN_D2 = 2;

/***** DEFINITION OF Software Serial *****/
const uint8_t myBluetooth_HC05_mySerial_PIN_SERIAL_TX_A0 = A0;
const uint8_t myBluetooth_HC05_mySerial_PIN_SERIAL_RX_A1 = A1;
SoftwareSerial myBluetooth_HC05_mySerial(myBluetooth_HC05_mySerial_PIN_SERIAL_RX_A1, myBluetooth_HC05_mySerial_PIN_SERIAL_TX_A0);

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
EasyButton button(pulsante_PushButton_PIN_D3);
DS18B20 sensor(sensor_DS18B20_DQ_PIN_D5);

int buttonPressCount = 0;

void setup(void)
{
  // put your setup code here, to run once:

  pinMode(pulsante_PushButton_PIN_D3, INPUT_PULLUP);
  pinMode(sensor_DS18B20_DQ_PIN_D5, INPUT);

  pinMode(led_LED_PIN_D2, OUTPUT);

  myBluetooth_HC05_mySerial.begin(9600);

  button.begin();
}

void loop(void)
{
  // put your main code here, to run repeatedly:

  button.read();

  if (button.wasPressed()) {
    buttonPressCount++;

    if (buttonPressCount == 3) {
      // Read the sensor and provide information on serial monitor
      float temperature = sensor.getTempC();
      Serial.print("Temperature: ");
      Serial.print(temperature);
      Serial.println(" °C");

      buttonPressCount = 0; // Reset button press count
    }
  }

  if (myBluetooth_HC05_mySerial.available()) {
    char c = myBluetooth_HC05_mySerial.read();
    if (c == 'o') {
      if (myBluetooth_HC05_mySerial.available()) {
        char c2 = myBluetooth_HC05_mySerial.read();
        if (c2 == 'k') {
          digitalWrite(led_LED_PIN_D2, LOW);
        }
      }
    }
  }
}