/********* Pleasedontcode.com **********

	Pleasedontcode thanks you for automatic code generation! Enjoy your code!

	- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

	- Project: Scanner
	- Source Code compiled for: Arduino Uno
	- Source Code created on: 2023-11-01 18:30:30
	- Source Code generated by: AlexWind

********* Pleasedontcode.com **********/
/****** DEFINITION OF LIBRARIES *****/
#include 
#include 
#include 
#include 
#include 

/****** SYSTEM REQUIREMENT 1 *****/
/* Reads NMEA 8bit data from GPS module. Reads hours */
/* minutes, seconds and Display h, m, s on LED */
/* display. When mins and secs are 00 00, contact */
/* closure for about 1 sec. */

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t enabler_PushButton_PIN_D3 = 3;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t contactClosure_PIN_D2 = 2;

/***** DEFINITION OF Software Serial *****/
const uint8_t gpsSerial_PIN_SERIAL_TX_A1 = A1;
const uint8_t gpsSerial_PIN_SERIAL_RX_A0 = A0;
SoftwareSerial gpsSerial(gpsSerial_PIN_SERIAL_RX_A0, gpsSerial_PIN_SERIAL_TX_A1);

/***** DEFINITION OF I2C PINS *****/
const uint8_t led_LCD1602I2C_I2C_PIN_SDA_A4 = A4;
const uint8_t led_LCD1602I2C_I2C_PIN_SCL_A5 = A5;
const uint8_t led_LCD1602I2C_I2C_SLAVE_ADDRESS = 39;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
LiquidCrystal_I2C lcd(led_LCD1602I2C_I2C_SLAVE_ADDRESS, 16, 2); // Initialize the LiquidCrystal_I2C object
MicroNMEA nmea;

void setup(void)
{
  // put your setup code here, to run once:

  pinMode(enabler_PushButton_PIN_D3, INPUT_PULLUP);

  pinMode(contactClosure_PIN_D2, OUTPUT);

  gpsSerial.begin(9600);

  lcd.begin(16, 2); // Initialize the LCD display
  lcd.backlight(); // Turn on the backlight
}

void loop(void)
{
  // put your main code here, to run repeatedly:

  if (gpsSerial.available())
  {
    char c = gpsSerial.read();
    nmea.process(c);
  }

  if (nmea.isValid())
  {
    uint8_t hour = nmea.getHour();
    uint8_t minute = nmea.getMinute();
    uint8_t second = nmea.getSecond();

    lcd.setCursor(0, 0);
    lcd.print("Time: ");
    lcd.print(hour);
    lcd.print(":");
    lcd.print(minute);
    lcd.print(":");
    lcd.print(second);

    if (minute == 0 && second == 0)
    {
      digitalWrite(contactClosure_PIN_D2, HIGH);
      delay(1000);
      digitalWrite(contactClosure_PIN_D2, LOW);
    }
  }
}