/********* Pleasedontcode.com **********

	Pleasedontcode thanks you for automatic code generation! Enjoy your code!

	- Terms and Conditions:
	You have a non-exclusive, revocable, worldwide, royalty-free license
	for personal and commercial use. Attribution is optional; modifications
	are allowed, but you're responsible for code maintenance. We're not
	liable for any loss or damage. For full terms,
	please visit pleasedontcode.com/termsandconditions.

	- Project: "Bluetooth Control"
	- Source Code NOT compiled for: Arduino Mega
	- Source Code created on: 2024-06-03 01:07:15

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
	/* Create a retro console on Arduino using */
	/* SoftwareSerial for dual Bluetooth HC-05 modules. */
	/* The system initializes serial communication at */
	/* 9600 baud for both modules, enabling wireless data */
	/* transfer. */
/****** END SYSTEM REQUIREMENTS *****/

/****** DEFINITION OF LIBRARIES *****/
#include 

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void updateOutputs(void);

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t myLED_RGB_LEDRGB_Red_PIN_D2 = 2;
const uint8_t myLED_RGB_LEDRGB_Green_PIN_D3 = 3;
const uint8_t myLED_RGB_LEDRGB_Blue_PIN_D4 = 4;

/***** DEFINITION OF Software Serial *****/
const uint8_t bluetooth_HC05_mySerial1_PIN_SERIAL_TX_A0 = A0;
const uint8_t bluetooth_HC05_mySerial1_PIN_SERIAL_RX_A1 = A1;
const uint8_t bluetooth_HC05_mySerial2_PIN_SERIAL_TX_A2 = A2;
const uint8_t bluetooth_HC05_mySerial2_PIN_SERIAL_RX_A3 = A3;

// Instantiate SoftwareSerial objects for both Bluetooth modules
SoftwareSerial bluetooth_HC05_mySerial1(bluetooth_HC05_mySerial1_PIN_SERIAL_RX_A1, bluetooth_HC05_mySerial1_PIN_SERIAL_TX_A0);
SoftwareSerial bluetooth_HC05_mySerial2(bluetooth_HC05_mySerial2_PIN_SERIAL_RX_A3, bluetooth_HC05_mySerial2_PIN_SERIAL_TX_A2);

/***** DEFINITION OF OUTPUT RAW VARIABLES *****/
/***** used to store raw data *****/
bool myLED_RGB_LEDRGB_Red_PIN_D2_rawData = 0;
bool myLED_RGB_LEDRGB_Green_PIN_D3_rawData = 0;
bool myLED_RGB_LEDRGB_Blue_PIN_D4_rawData = 0;

/***** DEFINITION OF OUTPUT PHYSICAL VARIABLES *****/
/***** used to store data after characteristic curve transformation *****/
float myLED_RGB_LEDRGB_Red_PIN_D2_phyData = 0.0;
float myLED_RGB_LEDRGB_Green_PIN_D3_phyData = 0.0;
float myLED_RGB_LEDRGB_Blue_PIN_D4_phyData = 0.0;

void setup(void)
{
    // put your setup code here, to run once:

    pinMode(myLED_RGB_LEDRGB_Red_PIN_D2, OUTPUT);
    pinMode(myLED_RGB_LEDRGB_Green_PIN_D3, OUTPUT);
    pinMode(myLED_RGB_LEDRGB_Blue_PIN_D4, OUTPUT);

    // Initialize both Bluetooth modules at 9600 baud
    bluetooth_HC05_mySerial1.begin(9600);
    bluetooth_HC05_mySerial2.begin(9600);
}

void loop(void)
{
    // put your main code here, to run repeatedly:

    updateOutputs(); // Refresh output data

    // Example of reading from one Bluetooth module and writing to another
    if (bluetooth_HC05_mySerial1.available())
    {
        char data = bluetooth_HC05_mySerial1.read();
        bluetooth_HC05_mySerial2.write(data);
    }

    if (bluetooth_HC05_mySerial2.available())
    {
        char data = bluetooth_HC05_mySerial2.read();
        bluetooth_HC05_mySerial1.write(data);
    }
}

void updateOutputs()
{
    digitalWrite(myLED_RGB_LEDRGB_Red_PIN_D2, myLED_RGB_LEDRGB_Red_PIN_D2_rawData);
    digitalWrite(myLED_RGB_LEDRGB_Green_PIN_D3, myLED_RGB_LEDRGB_Green_PIN_D3_rawData);
    digitalWrite(myLED_RGB_LEDRGB_Blue_PIN_D4, myLED_RGB_LEDRGB_Blue_PIN_D4_rawData);
}

/* END CODE */